Skip to main content
Welcome to Absolute Energy

Blown Insulation for Commercial Renovations: Lessons From Our Own Office

Commercial Insulation Install for Renovations - Trufill

Commercial renovations rarely start with a blank slate. Offices, shops and workspaces have often been extended, altered and repaired many times. As a result, once the linings come off, the framing behind them is rarely uniform. That’s where blown insulation for commercial renovations comes into its own.

For most buildings, insulation batt or segment products are a great choice. After all, they’re affordable, they perform well and our team installs them every day. However, when framing is irregular, traditional insulation can be hard to fit properly. That leaves gaps where heat escapes.

We ran into exactly this problem when we renovated our own office. In the end, traditional insulation was not the answer for those walls. Blown insulation was.

Case study: renovating the Absolute Energy office

Commercial Renovation Results

Our head office in Nelson had been Absolute Energy’s base for more than 20 years. Over that time, our team had spread across several buildings. So we brought everyone together under one roof with a six-month renovation. We worked alongside JTB Architects, designer Lyn Russell and Scott Construction.

However, once the old linings came off, we found the framing was far from standard. For example:

  • Stud spacing varied from bay to bay, with few standard widths
  • Some timber had bowed or twisted, so cavity depths weren’t consistent
  • Dwangs (nogs) sat at different heights, creating lots of small, odd-shaped spaces

In fact, these conditions are common in commercial buildings that have changed over the years, from offices and retail spaces to clinics and workshops. We see them regularly across Nelson, Tasman and Marlborough. So our own office became a useful test of the best way to insulate them.

Alongside the walls, we also used Trufill in the floors and ceilings. The finished space now doubles as our showroom, so clients, builders and project managers can see these products up close. You can take a look inside our new office to see how it all came together.

Why traditional insulation was not the best fit for these walls

Most manufacturers make batt or segment style products in standard widths and thicknesses to suit modern framing. For example, in a new build, studs sit at regular centres. As a result, a segment slips in neatly and fill the cavity edge to edge. In buildings like this, traditional insulation provides an excellent choice.

Irregular framing, however, changes that. To make traditional insulation work, our installers would have to cut and trim almost every piece. Even with careful work, this can lead to:

  • Small gaps along the edges of cut segment without extra attention
  • Compression where installers force a batt into a narrower or shallower space, which lowers its R-value, and is time consuming
  • Voids around dwangs, cabling and odd-shaped pockets, which are always a challenge

Each gap is small on its own. Together, however, they add up to cold spots and lost heat across the wall. On top of that, all that trimming creates offcuts and waste. Blown insulation avoids both problems.

Our solution: Trufill blown insulation

Commercial Insulation Install - Trufill

For the office, we chose Trufill, a blown insulation system from Safe-R Insulation. Essentially, it’s a dry, loose-fill glass wool that our installers blow into the framing as one continuous fill.

Trufill isn’t a wet foam or a spray foam, It’s dry blown fibreglass. In fact, Safe-R makes it’s blown fibreglass from up to 80% recycled glass.

Here’s how it works in an open wall:

  1. First, our installer fixes a clear Blown Insulation Barrier (a strong mesh) across the face of the framing.
  2. Next, they blow the glass wool in behind the mesh, bay by bay.
  3. As it goes in, the fill packs into every corner and around dwangs and services, whatever the shape of the cavity.
  4. Finally, the builder fixes the new wall linings over the mesh, as normal.

Because the mesh is clear, our team can see each bay fill completely before the linings go on. And because Trufill is blown on site, our installers can adjust its density to suit each part of the building, from walls to floors and skillion roofs.

Trufill is also non-combustible. In addition, it holds a CodeMark certificate for use in framed walls, floors, skillion roofs and ceilings. As a result of its adjustable density, it can hit the R-value a project needs. For example, Trufill can reach R4.2 in a standard 140mm wall and R7.3 in a 240mm roof cavity.

Safe-R designed Trufill for new builds, and it’s a popular choice there too. You can read more in our guide to Trufill blown insulation for new builds. However, as our office showed, it works just as well in any commercial renovation where the framing is open.

The benefits of blown insulation in commercial renovations

Commercial Insulation Ceiling Install
  • No gaps. The fill takes the exact shape of each cavity. As a result, there are no edges, joins or missed corners for heat to escape through.
  • No compression. Because nothing gets squeezed into a space that’s too small, the insulation performs as rated.
  • Works with any framing. Uneven stud spacing, varying cavity depths and odd-shaped bays all fill the same way.
  • Fills around services. Commercial walls often carry data cabling, plumbing and electrical runs. Blown insulation fills around them without leaving voids.
  • No waste. There’s no cutting segments to fit each bay, so there are no offcuts to throw away.
  • Lower carbon footprint. Blown insulation is highly compressed for transport. Therefore, it takes less energy to freight than many equivalent products.
  • A quieter workplace. A dense, continuous fill helps keep heat in and reduce noise between rooms. Paired with acoustic panels for commercial offices, it helps staff focus.
  • Non-combustible. Glass wool won’t burn, which gives you peace of mind in a busy workplace.

Overall, the result is a warmer, more comfortable office that holds its heat. In turn, lower heating and cooling demand helps keep running costs down.

Other insulation options for commercial renovations

Blown insulation suits buildings like our office, but it’s just one tool in a full kit. In fact, Absolute Energy installs a complete range of insulation, so we can match the product to each part of your building. Here are some of the other options we often recommend.

  • Insulation segments. Where framing is regular, fibreglass, polyester or wool segments are often the simplest and most cost-effective choice. They’re quick to install and perform reliably for years.
  • CosyWall blown wall insulation. If the walls are still lined, our installers can add CosyWall through small holes in the internal linings. This service covers Nelson, Tasman and Marlborough. Read how we retrofit wall insulation without removing the Gib.
  • Blown ceiling insulation. For tight or hard-to-reach roof spaces, blown ceiling insulation gives full coverage without major disruption.
  • Underfloor insulation. Where floors are accessible, underfloor insulation helps keep the space warmer underfoot.
  • Acoustic insulation and panels. For meeting rooms and open-plan offices, acoustic panels help control noise and improve focus.
  • Insulation removal. If old ceiling insulation is damaged or compressed, we can remove and dispose of it before installing new products.

Planning a refit? If so, bring insulation into the conversation early. We work with architects, builders and project managers from the design stage. Learn more about our commercial insulation services.

Frequently asked questions

Can blown insulation be used in commercial buildings? Yes. Trufill holds a CodeMark certificate for framed walls, floors, skillion roofs and ceilings. In fact, we used it throughout our own commercial office.

What is blown insulation? Blown insulation is a loose-fill material, such as glass wool, that a machine blows into a cavity. Unlike segments, which installers cut to size, it fills the space completely. It’s also a dry fibre, not a wet foam or spray foam.

Is blown insulation better than batt or segment type products? Neither is better in every building. Traditional insulation suits regular, modern framing. Blown insulation, on the other hand, suits irregular framing and awkward spaces where an insulation batt or segment are hard to fit without gaps.

Can blown insulation go into walls that are already lined? Yes, but with a different system. For closed walls, we use CosyWall, which our installers add through small holes in the internal linings across Nelson, Tasman and Marlborough. Trufill, by contrast, goes in while the framing is exposed and held in place by a special membrane, as it did in our office.

Will blown insulation settle over time? Our installers blow Trufill to a set density for each application, in line with its certification. As a result, it’s designed to keep performing over time.

Is blown insulation safe? Yes. Trufill is a glass wool product, and it’s non-combustible. It also contains no binder, so there are no VOCs or off-gassing.

Get the right insulation for your commercial renovation

Every commercial building is different. In the end, the best insulation depends on what’s behind the walls. That’s why our team will assess the space first. Then we’ll work with your architect and builder to recommend the right product for each area.

Absolute Energy has insulated more than 25,000 homes and commercial buildings across the South Island. Our head office and showroom is in Nelson, and our wall insulation crews are local to Nelson, Tasman and Marlborough. To discuss your project, get in touch with our team or call us on 0800 423 454.

We also cover Dunedin, Queenstown and the wider Otago region. If you’re outside our wall insulation area, give us a call anyway and we’ll let you know how we can help. Learn more about insulation in Dunedin and Queenstown.

Sources: A Peak Inside Absolute Energy’s New Space · Trufill Insulation System (Safe-R) · Trufill for New Builds (Safe-R) · Trufill CodeMark CMNZ30144 (MBIE)